Printer image

Votre imprimante laser HP Color LaserJet CM6040, CM6040F
est en panne ?

Notre technicien peut intervenir sur site
pour la dépanner.

Nos spécialistes sont en mesure de prendre en charge toutes les pannes :

Indiquez-nous la panne rencontrée pour obtenir un diagnostic.

  • Défauts d’impression (traces, points, traits...)
  • Bourrages papier (départ papier, feuille froissée en accordéon...)
  • Message ou code erreur
  • Fuite de toner
  • Bruit anormal
  • Panne électronique
  • Paramétrage
  • Accessoire
  • Pièce détachée
  • Machine complète

... ou le code erreur qui s'affiche sur l'écran de votre imprimante.

Codes erreur rencontrés fréquemment sur l'imprimante
HP Color LaserJet CM6040, CM6040F

Le code affiché sur votre imprimante est plus long que celui indiqué dans cette liste.
Par exemple si l'écran de l'imprimante indique un code 13.00.02, nous ne retenons que le début du code, c'est à dire 13.
Le code 13 renvoie à un type de problème, les chiffres qui suivent pouvant apporter une précision.

printer-icon

Code erreur 10 : Problème de mémoire consommable, puce HS


Code erreur 13 : Bourrage papier


Code erreur 41 : Format de papier inattendu


Code erreur 49 : Format de fichier incorrect (pdf ou autre) ou pb de firmware


Code erreur 50 ou Erreur Station fusion ou Remplacer kit de maintenance : Problème de four (kit de maintenance)


Code erreur 51 : Panne de moteur laser


Code erreur 57 : Panne de ventilateur


Code erreur 59 : Panne de moteur


Tableau de tous les codes erreur de la HP Color LaserJet CM6040, CM6040F

10.00.YY

- code :

10.00.YY

- affichage :

10.00.YY Supply memory error (print cartridge)

- description :

data. The print cartridge is present but defective.
• 10.00.00 Supply memory error (black print cartridge) • 10.00.01 Supply memory error (cyan print cartridge) • 10.00.02 Supply memory error (magenta print cartridge) • 10.00.03 Supply memory error (yellow print cartridge)

10.10.YY

- code :

10.10.YY

- affichage :

10.10.YY Supply memory error (missing elabel)

- description :

The product cannot read or write to at least one e-label, or at least one e-label is missing.
• 10.10.00 Supply memory error (e-label for the black print cartridge) • 10.10.01 Supply memory error (e-label for the cyan print cartridge) • 10.10.02 Supply memory error (e-label for the magenta print cartridge) • 10.10.03 Supply memory error (e-label for the yellow print cartridge) • 10.10.05 Supply memory error (e-label for the black image drum) • 10.10.06 Supply memory error (e-label for the cyan image drum) • 10.10.07 Supply memory error (e-label for the magenta image drum) • 10.10.08 Supply memory error (e-label for the yellow image drum)M€

10.90.XY

- code :

10.90.XY

- affichage :

10.90.XY - Replace <color> Cartridge

- description :

A toner replenishment malfunction occurred and the toner concentration in the image drum dropped below 30%. This applies to both HP and non-HP print cartridges.
• 10.90.00 - Replace Black Cartridge • 10.90.01 - Replace Cyan Cartridge • 10.90.02 - Replace Magenta Cartridge • 10.90.03 - Replace Yellow Cartridge

10.xx.yy

- code :

10.xx.yy

- affichage :

10.xx.yy Supply Memory Error

- description :

The product cannot read or write to at least one print cartridge e-label, or an e-label is missing from a print cartridge.

11.XX

- code :

11.XX

- affichage :

11.XX Internal clock error

- description :

The product's real time clock experienced an error.

13.01

- code :

13.01

- affichage :

13.01 Paper feed 1, Paper late jam

- description :

• The leading edge of the paper fed from Tray 1 stopped before reaching the registration sensor (C). • The leading edge of the paper fed from Tray 2 stopped before reaching the registration sensor (B). • The leading edge of the paper fed from Tray 3 stopped before reaching the registration sensor (A-1). • The leading edge of the paper fed from Tray 4 stopped before reaching the registration sensor (A-2). • The leading edge of the paper fed from Tray 5 stopped before reaching the registration sensor (A-3).89A

13.02

- code :

13.02

- affichage :

13.02 Paper Stop Jam In Tray 2 at Sensor D

- description :

The paper stopped at the registration sensor (D).

13.05

- code :

13.05

- affichage :

13.05 Paper Late Jam Between Sensors D and F

- description :

The leading edge of the paper stopped between the registration sensor (D) and the fuser-output sensor (F).

13.06

- code :

13.06

- affichage :

13.06 Paper Jam In Fuser

- description :

The paper stopped at the fuser-output sensor (F).

13.10

- code :

13.10

- affichage :

13.10 Paper Late Jam In Duplex Area Sensors F - G

- description :

The leading edge of the paper stopped between the output sensor (F) and switchback sensor (G).

13.11

- code :

13.11

- affichage :

13.11 Paper Stop Jam In Duplex Area at Sensor G

- description :

The paper stopped at the switchback-jam sensor (G).

13.12

- code :

13.12

- affichage :

13.12 Paper Late Jam In Duplex Area Sensors H - D

- description :

The duplex refeed paper stopped between the duplexer-delivery sensor (H) and the registration sensor (D).

13.12.11

- code :

13.12.11

- affichage :

13.12.11

- description :

Finisher stay jam at either PI33 or PI34 when engine powered on. When the engine is powered on, the finisher's upper-feed-path-entry sensor (PI33) or the upper-feed-path-exit sensor (PI34) is activated suggesting that there is paper in the upper paper path of the finisher at sensors PI33 or PI34.

13.12.12

- code :

13.12.12

- affichage :

13.12.12

- description :

Finisher delay jam at PI33. The engine signals the finisher that paper is about to enter the finisher from the IPTU. The finisher's upper-feed-path-entry sensor (PI33), which detects paper entering the finisher, does not detect the paper within the expected time period triggering the error.

13.12.13

- code :

13.12.13

- affichage :

13.12.13

- description :

Finisher stay jam at PI33. Finisher's upper-feed-path-entry sensor (PI33) is remaining activated longer than expected, suggesting that paper has jammed at the sensor.

13.12.14

- code :

13.12.14

- affichage :

13.12.14

- description :

Finisher delay jam at PI34. Upper-paper-path-entry sensor (PI33) has signaled that paper has passed but upperpaper- path-exit sensor PI34 does not actuate within the expected time, suggesting that the paper has jammed between PI33 and PI34 in the upper paper path.

13.12.15

- code :

13.12.15

- affichage :

13.12.15

- description :

Finisher stay jam at PI34 Finisher's upper-paper-path-exit sensor (PI34) remains activated longer than expected suggesting that paper has jammed at the sensor.

13.12.16

- code :

13.12.16

- affichage :

13.12.16

- description :

Finisher jam - door opened during Staple/ Stacking operation While the machine is printing, the upper-door (open/close) sensor (PI31) or front-door (open/close) sensor (PI32) or the front-door (open/close) switch (MSW31) has signaled that one of the doors has been opened, suggesting that there may now be paper found in the upper paper path.

13.12.17

- code :

13.12.17

- affichage :

13.12.17

- description :

Engine to finisher timing jam: unexpected arrival of paper to finisher Upper-paper-path-entry sensor (PI33) has detected paper before a signal from the engine has been received, indicating that paper is being delivered from the IPTU to the finisher.

13.12.21

- code :

13.12.21

- affichage :

13.12.21

- description :

Finisher upper-stapler (stapler 1) staple jam. When the staple motor (M41) is rotated forward, the staple home-position sensor (PI5) does not turn back on after the prescribed time has elapsed after it goes off, and the staple home-position sensor (PI50) turns on within the prescribed time after the staple motor (M41) is rotated backwards.

13.12.41

- code :

13.12.41

- affichage :

13.12.41

- description :

Finisher - Paper detected in booklet making portion of finisher at engine power on. Occurs when paper is detected by one of the sensors on the paper-sensor board (PI18, PI19, PI20), vertical-path-paper sensor (PI17), booklet-delivery sensor (PI11), paperpositioning- plate paper sensor (PI8), or booklet-making paper-entry sensor (PI22) when the machine is powered on.

13.12.42

- code :

13.12.42

- affichage :

13.12.42

- description :

Finisher delay jam at booklet-making paperentry sensor (PI22) Occurs when booklet making function is selected and after the engine signals the finisher that it is delivering paper to the finisher. The booklet-making paper-entry sensor (PI22) is not activated within the expected time period after receiving the engine's delivery signal, suggesting that a paper jam has occurred somewhere between the output accessory bridge (IPTU) and sensor PI22.

13.12.43

- code :

13.12.43

- affichage :

13.12.43

- description :

Finisher stay jam at booklet-making paperentry sensor (PI22) Occurs when the booklet-making paper-entry sensor (PI22) remains activated longer than expected, suggesting that there is a paper jam at the sensor.

13.12.44

- code :

13.12.44

- affichage :

13.12.44

- description :

Finisher delay jam at booklet-making firstpaper sensor (PI18) Occurs when the first-paper sensor (PI18) is not activated within the expected time following the activation of the booklet-making paper-entry sensor (PI22), suggesting that there is a paper jam in the area between PI22 and PI18.

13.12.45

- code :

13.12.45

- affichage :

13.12.45

- description :

Finisher stay jam at booklet-making firstpaper sensor (PI18), flapper-1 paper sensor (PI19) or flapper-2 paper sensor (PI20) Occurs when PI18, PI19 or PI20 remain activated longer than expected, suggesting that there is a paper jam in the flapper 1 and 2 area of the booklet-maker section of the finisher.

13.12.46

- code :

13.12.46

- affichage :

13.12.46

- description :

Finisher jam - door was opened during booklet making operation. Occurs while the machine is booklet making and the booklet-delivery-door sensor (PI3) or the booklet-paper-path open/close sensor (PI3) detects that the door or paper path has been opened. Also occurs when the finisher's front-door sensor (PI32) has been opened with paper remaining in the processing tray of the main stapler while the finisher is not operating.

13.12.51

- code :

13.12.51

- affichage :

13.12.51

- description :

Finisher jam: rear booklet stapler (SW5) When the rear-staple motor (M6) is rotated forward, the staple home-position sensor (SW5) does not turn back on after the prescribed time has elapsed after it goes off (0.4 seconds).

13.12.52

- code :

13.12.52

- affichage :

13.12.52

- description :

Finisher jam: front-booklet stapler (SW7) When the rear-staple motor (M7) is rotated forward, the staple home-position sensor (SW7) does not turn back on after the prescribed time has elapsed after it goes off (0.4 seconds).

13.12.61

- code :

13.12.61

- affichage :

13.12.61

- description :

Finisher delay jam at the booklet-delivery sensor (PI11) Occurs when the folded booklet exits the folding rollers and does not reach the bookletdelivery sensor (PI11) within the expected time.

13.12.62

- code :

13.12.62

- affichage :

13.12.62

- description :

Finisher stay jam at the booklet-delivery sensor (PI11) or the vertical-paper-path sensor (PI17) Occurs when the booklet-delivery sensor (PI11) remains activated longer than expected after sensing the arrival of the new booklet from the folding rollers. Also occurs when the vertical-paper-path sensor (PI17) remains activated longer than expected after the paper has already passed through the folding rollers and is now detected by the booklet-delivery sensor (PI11).

13.13

- code :

13.13

- affichage :

13.13 Paper Stop Jam In Duplex Area Sensors G - H

- description :

The duplex refeed paper stopped between the switchback sensor (G) and the duplexerdelivery sensor (H).

13.1C

- code :

13.1C

- affichage :

13.1C Fuser Wrap Jam, Paper in Fuser

- description :

The paper is wrapping at the fuser.

13.20

- code :

13.20

- affichage :

13.20 Paper Eject Jam at Sensors E, F - G

- description :

The paper stopped at either the loop sensor (E), the fuser-output sensor (F) or the switchback sensor (G).

13.21

- code :

13.21

- affichage :

13.21 Door Open Jam

- description :

The paper position is unknown.

13.2B

- code :

13.2B

- affichage :

13.2B Paper Stop Jam In Output Accessory Bridge

- description :

The paper stopped before reaching IPTU sensor 1 (K).

13.2C

- code :

13.2C

- affichage :

13.2C Paper Late Jam in Output Accessory Bridge (1)

- description :

The paper stopped between IPTU sensor 1 (K) and IPTU sensor 3 (M).

13.2D

- code :

13.2D

- affichage :

13.2D Paper Late Jam in Output Accessory Bridge (2)

- description :

The paper stopped in the path along IPTU sensor 1 (K), IPTU sensor 2 (L), and IPTU sensor 3 (M).

13.2E

- code :

13.2E

- affichage :

13.2E Paper Late Jam Near Fuser at Sensors F - J

- description :

The paper stopped between the fuser-output sensor (F) and the output-bin-full sensor (J).

13.30

- code :

13.30

- affichage :

13.30 Paper Late Jam, Jam In Cassette

- description :

• The leading edge of the paper fed from Tray 1 stopped before reaching the registration sensor (D). • The leading edge of the paper fed from Tray 2 stopped before reaching the registration sensor (D). • The leading edge of the paper fed from Tray 3 stopped before reaching the registration sensor (D). • The leading edge of the paper fed from Tray 4 stopped before reaching the registration sensor (D). • The leading edge of the paper fed from Tray 5 stopped before reaching the registration sensor (D).

13.7C

- code :

13.7C

- affichage :

13.7C Delivery Delay Jam 1

- description :

There is a delay in reaching the first IPTU sensor.

13.7D

- code :

13.7D

- affichage :

13.7D Delivery Delay Jam 2

- description :

There is a delay in reaching the last IPTU sensor.

13.7E

- code :

13.7E

- affichage :

13.7E Delivery Delay Jam 3

- description :

There is a delay in reaching the output rollers from the fuser.

13.80

- code :

13.80

- affichage :

13.80 External Output Device Paper Jam

- description :

There is a delivery jam on the IPTU between the first and last sensor.

13.90

- code :

13.90

- affichage :

13.90 Non-specific Paper Jam

- description :

The leading edge of the paper is at the registration sensor (D).

13.JJ.NT

- code :

13.JJ.NT

- affichage :

13.JJ.NT- Jam below control panel

- description :

A jam occurred below the control panel.

13.XX.YY

- code :

13.XX.YY

- affichage :

13.XX.YY Jam inside output accessory bridge

- description :

There is a paper jam inside the outputaccessory bridge (IPTU).

20

- code :

20

- affichage :

20 INSUFFICIENT MEMORY

- description :

The product does not have enough memory to print the page.

22

- code :

22

- affichage :

22 EMBEDDED I/O BUFFER OVERFLOW

- description :

Too much data was sent to the embedded HP Jetdirect print server. An incorrect communications protocol might be in use.

30.01.02

- code :

30.01.02

- affichage :

30.01.02 Scanner failure

- description :

The ADF is jammed or the sensor failed.

30.01.03

- code :

30.01.03

- affichage :

30.01.03 Scanner failure

- description :

An ADF pickup failure occurred.

30.01.06

- code :

30.01.06

- affichage :

30.01.06 Scanner failure

- description :

The scanner-lamp fan failed.

30.01.08

- code :

30.01.08

- affichage :

30.01.08 Scanner failure

- description :

The scanner is locked, or the home sensor or flat cable failed.

30.01.14

- code :

30.01.14

- affichage :

30.01.14 Scanner failure

- description :

The SCB firmware failed.

30.01.15

- code :

30.01.15

- affichage :

30.01.15 Scanner failure

- description :

The scanner initialization failed.

30.01.18

- code :

30.01.18

- affichage :

30.01.18 Scanner failure

- description :

The SCB ASIC failed.

30.01.19

- code :

30.01.19

- affichage :

30.01.19 Scanner failure

- description :

The scanner lamp failed.

30.01.25

- code :

30.01.25

- affichage :

30.01.25 Scanner failure

- description :

The copy-process board (CPB) failed.

30.01.34

- code :

30.01.34

- affichage :

30.01.34 Scanner failure

- description :

The scanner initialization failed, and the copy-process board (CPB) cannot communicate with the scanner-control board (SCB).

30.01.39

- code :

30.01.39

- affichage :

30.01.39 Scanner failure

- description :

There was an AFE1 (analog front-end) failure.

30.01.40

- code :

30.01.40

- affichage :

30.01.40 Scanner failure

- description :

The scanner AFE 2 failed.

30.01.41

- code :

30.01.41

- affichage :

30.01.41 Scanner failure

- description :

There was a CPB error.

30.01.42

- code :

30.01.42

- affichage :

30.01.42 Scanner failure

- description :

The scanner cable is disconnected

30.01.43

- code :

30.01.43

- affichage :

30.01.43 Scanner failure

- description :

The CPB memory is full.

30.01.44

- code :

30.01.44

- affichage :

30.01.44 Scanner failure

- description :

There is an SCB communication error.

30.01.45

- code :

30.01.45

- affichage :

30.01.45 Scanner failure

- description :

The CPB memory is full.

30.01.46

- code :

30.01.46

- affichage :

30.01.46 Scanner failure

- description :

The CPB enumeration failed.

40

- code :

40

- affichage :

40 Embedded I/O Bad Transmission

- description :

A temporary printing error occurred. The connection between the product and the EIO card in the specified slot has been broken.

41.3

- code :

41.3

- affichage :

41.3 Load Tray <XX>: [Type] [Size]

- description :

The specified tray is loaded with media that is longer or shorter in the feed direction than the size adjusted for the tray. This message also appears if two or more sheets of media stick together in the product or if the tray is not adjusted correctly. If using glossy paper, ensure that it has been acclimated.

41.5

- code :

41.5

- affichage :

41.5 Load Tray <XX>: [Type], [Size] To use another tra

- description :

The product detected an unexpected paper size. There is a tray type mismatch. The tray is a cassette and there is another tray available for use.

41.X

- code :

41.X

- affichage :

41.X ERROR

- description :

A temporary printing error occurred.

48.01

- code :

48.01

- affichage :

48.01 Transfer unit error

- description :

The ITB top sensor malfunctioned.

49.XXXXX

- code :

49.XXXXX

- affichage :

49.XXXXX ERROR

- description :

A critical firmware error occurred.

50.1

- code :

50.1

- affichage :

50.1 Fuser error

- description :

The fuser experienced a low-temperature error while printing or after it warmed up.

50.2

- code :

50.2

- affichage :

50.2 Fuser error

- description :

The fuser experienced a warm-up error.

50.3

- code :

50.3

- affichage :

50.3 Fuser error

- description :

The fuser experienced a high-temperature error.

50.4

- code :

50.4

- affichage :

50.4 Fuser error

- description :

There was an error with the fuser drive circuit.

50.5

- code :

50.5

- affichage :

50.5 Fuser error

- description :

The fuser experienced a type-mismatch error.

50.7

- code :

50.7

- affichage :

50.7 Fuser error

- description :

The fuser experienced a pressure-release mechanism error.

50.8

- code :

50.8

- affichage :

50.8 Fuser error

- description :

The fuser experienced a low-temperature error.

50.9

- code :

50.9

- affichage :

50.9 Fuser error

- description :

The fuser experienced a high-temperature error.

50.A

- code :

50.A

- affichage :

50.A Fuser Error

- description :

There is a low-temperature error.

50.B

- code :

50.B

- affichage :

50.B Fuser Error

- description :

There is a high-temperature error.

51.1Y

- code :

51.1Y

- affichage :

51.1Y Error

- description :

There is a beam detect error. • 51.10=black • 51.11=cyan • 51.12=magenta • 51.13=yellow

51.2Y

- code :

51.2Y

- affichage :

51.2Y Error

- description :

There is a laser error.
• 51.20=black • 51.21=cyan • 51.22=magenta • 51.23=yellow

52.00

- code :

52.00

- affichage :

52.00 Error

- description :

The scanner experienced a startup error.

52.10

- code :

52.10

- affichage :

52.10 Error

- description :

There is a laser scanner startup error.

52.20

- code :

52.20

- affichage :

52.20 Error

- description :

The scanner experienced a rotational error.

53.10.0X

- code :

53.10.0X

- affichage :

53.10.0X Unsupported DIMM

- description :

An unsupported DIMM is installed.

54.01

- code :

54.01

- affichage :

54.01 Error

- description :

The environmental sensor experienced an error.

54.15

- code :

54.15

- affichage :

54.15 Error

- description :

The yellow-toner-level sensor experienced an error.

54.16

- code :

54.16

- affichage :

54.16 Error

- description :

The magenta-toner-level sensor experienced an error.

54.17

- code :

54.17

- affichage :

54.17 Error

- description :

The cyan-toner-level sensor experienced an error.

54.18

- code :

54.18

- affichage :

54.18 Error

- description :

The black-toner-level sensor experienced an error.

55.00.YY

- code :

55.00.YY

- affichage :

55.00.YY DC Controller Communication Error

- description :

The DC controller experienced a communication error.

55.01.YY

- code :

55.01.YY

- affichage :

55.01.YY DC Controller Memory Error

- description :

There is an error with the DC controller memory.

55.02.YY

- code :

55.02.YY

- affichage :

55.02.YY Outgoing Parity Error

- description :

There is a DC controller outgoing parity error.

55.03.YY

- code :

55.03.YY

- affichage :

55.03.YY No Engine Responsesupply unit.

- description :

DC controller no response error.

55.04.YY

- code :

55.04.YY

- affichage :

55.04.YY Communications Timeout

- description :

There was a DC controller communications timeout.

55.05

- code :

55.05

- affichage :

55.05 Error

- description :

An interruption occurred during a remote firmware update.

56.01

- code :

56.01

- affichage :

56.01 - Illegal input

- description :

There was an illegal input.

56.02

- code :

56.02

- affichage :

56.02 - Illegal output

- description :

There was an illegal output.

57.01

- code :

57.01

- affichage :

57.01 Error

- description :

The VOC fan (FM4) experienced an error.

57.03

- code :

57.03

- affichage :

57.03 Error

- description :

The fuser cooling fan (FM2) experienced an error.

57.04

- code :

57.04

- affichage :

57.04 Error

- description :

The cartridge-area cooling fan (FM3) experienced an error.

57.05

- code :

57.05

- affichage :

57.05 Error

- description :

The low-voltage power-supply cooling fan (FM5) experienced an error.

57.06

- code :

57.06

- affichage :

57.06 Error

- description :

The cartridge-front-area cooling fan (FM6) experienced an error.

57.07

- code :

57.07

- affichage :

57.07 Error

- description :

The laser/scanner-unit cooling fan (FM1) experienced an error.

57.08

- code :

57.08

- affichage :

57.08 Error

- description :

The delivery-unit cooling fan (FM7) experienced an error.

57.09

- code :

57.09

- affichage :

57.09 Error

- description :

The scanner fan or control panel fan has failed.

59.30

- code :

59.30

- affichage :

59.30 Error

- description :

The fuser motor experienced a startup error.

59.40

- code :

59.40

- affichage :

59.40 Error

- description :

The fuser motor experienced a rotational error.

59.50

- code :

59.50

- affichage :

59.50 Error

- description :

The black-image-drum motor experienced a startup error.

59.51

- code :

59.51

- affichage :

59.51 Error

- description :

The cyan-image-drum motor experienced a startup error.

59.52

- code :

59.52

- affichage :

59.52 Error

- description :

The magenta-image-drum motor experienced a startup error.

59.53

- code :

59.53

- affichage :

59.53 Error

- description :

The yellow-image-drum motor experienced a startup error.

59.60

- code :

59.60

- affichage :

59.60 Error Black Image Drum Motor rotation error

- description :

The black-image-drum motor experienced a rotational error.

59.61

- code :

59.61

- affichage :

59.61 Error

- description :

The cyan-image-drum motor experienced a rotational error.

59.62

- code :

59.62

- affichage :

59.62 Error

- description :

The magenta-image-drum motor experienced a rotational error.

59.63

- code :

59.63

- affichage :

59.63 Error

- description :

The yellow-image-drum motor experienced a rotational error.

59.90

- code :

59.90

- affichage :

59.90 Error

- description :

The ITB motor rotated abnormally.

59.A0

- code :

59.A0

- affichage :

59.A0 Error

- description :

The ITB motor rotated abnormally.

59.C0

- code :

59.C0

- affichage :

59.C0 Error

- description :

The developer-disengagement motor experienced a rotational error.

59.F0

- code :

59.F0

- affichage :

59.F0 Error

- description :

The primary-transfer-roller disengagement motor experienced an error.

59.XY

- code :

59.XY

- affichage :

59.XY ERROR

- description :

A temporary printing error occurred.

60.02

- code :

60.02

- affichage :

60.02 Tray 2 lifting error

- description :

The Tray 2 lifter motor experienced an error.

60.03

- code :

60.03

- affichage :

60.03 Tray 3 lifting error

- description :

The Tray 3 lifter motor experienced an error

60.04

- code :

60.04

- affichage :

60.04 Tray 4 lifting error

- description :

The Tray-4 lifter motor experienced an error.

60.05

- code :

60.05

- affichage :

60.05 Tray 5 lifting error

- description :

The Tray 5 lifter motor experienced an error.

60.XX

- code :

60.XX

- affichage :

60.<XX> Tray <X> lifting error

- description :

The tray number specified by <XX> is in the process of lifting the paper to the top of the tray for proper feeding, and an obstruction prevents the tray from lifting properly.

65.12.99

- code :

65.12.99

- affichage :

65.12.99 Output accessory disconnected

- description :

An external paper-handling product connection has been interrupted.

66.00.15

- code :

66.00.15

- affichage :

66.00.15. External Device Failure

- description :

This error occurs if the external device upgrade is not accomplished in a specified time frame. This forces the PHC to crash, and the user will have to turn the product off and then on and attempt the upgrade again.

66.12.01

- code :

66.12.01

- affichage :

66.12.01

- description :

Finisher to engine communication error The communication between the print engine and the finisher has been interrupted or lost.

66.12.02

- code :

66.12.02

- affichage :

66.12.02

- description :

Finisher board communication error Occurs when the finisher's stacker-controller board has had a internal communication problem between the two processors on the board.

66.12.03

- code :

66.12.03

- affichage :

66.12.03

- description :

Finisher control board RAM error The checksum for the finisher stacker controller PCA has an error when the power is turned on.

66.12.11

- code :

66.12.11

- affichage :

66.12.11

- description :

Finisher error: swing motor (M36) and the swing-guide home-position sensor (PI35) Occurs when the swing guide does not leave its home position (swing-guide home-position sensor: PI35) after the swing motor (M36) is activated for 3 seconds. Also occurs when the swing guide does not return to its home position (swing-guide home-position sensor: PI35) after the swing motor (M36) is activated for 3 seconds.

66.12.12

- code :

66.12.12

- affichage :

66.12.12

- description :

Finisher error - shutter movement malfunction Normal operation: When the shutter clutch (CL31) and stack-ejection lower-roller clutch (CL32) are on, the shutter moves up (closed) when the stack-ejection motor (M32) turns forward and moves down (open, delivery enabled) when the motor turns backwards. Error occurs when the shutter home-position sensor (PI45) indicates no change when the stack-ejection motor (M32) is activated for 3 seconds, indicating that the shutter is not moving.

66.12.13

- code :

66.12.13

- affichage :

66.12.13

- description :

Finisher error - stack trailing-edge motor (M39) In order to improve stacking performance when ejecting copies, a trailing-edge assist guide is used in addition to the stack-ejection roller to support the rear end of the stack during stack ejection. Error occurs when the stacker trailing-edge guide does not leave its home position (PI39) after the stack trailing-edge motor (M39) has been turned on for 3 seconds.

66.12.14

- code :

66.12.14

- affichage :

66.12.14

- description :

Finisher stapling and offsetting front-aligningplate motor failure In order to neatly align the paper stack for either stapling or offsetting to take place, the front and rear aligning plates move to align each sheet when it enters the processing tray. The error occurs when the aligning plate either does not leave or when it does not return to the aligning-plate front-homeposition sensor (PI36) when the frontaligning- plate motor (M33) has been driven for 4 seconds.

66.12.15

- code :

66.12.15

- affichage :

66.12.15

- description :

Finisher stapling or offsetting rear-aligningplate motor failure (M34) In order to neatly align the paper stack for either stapling or offsetting to take place, the front and rear aligning plates move to align each sheet when it enters the processing tray. The error occurs when the aligning plate either does not leave or when it does not return to the aligning-plate rear- home- position sensor (PI37) when the rearaligning- plate motor (M34) has been driven for 4 seconds.

66.12.16

- code :

66.12.16

- affichage :

66.12.16

- description :

Finisher error - speed-change motor (M40) The speed-change motor M40 and sensor PI49 associated with this error have been removed from the output device prior to introduction to the field. This error message should never be seen in the field.

66.12.21

- code :

66.12.21

- affichage :

66.12.21

- description :

Finisher upper-stapler motor failure (M41) Error occurs either when the stapler does not leave stapler home position (PI50) after staple motor (M41) is driven for 0.4 seconds or when it does not return to stapler home position after the staple motor has detected a motor-lock condition and the motor is driven backwards for 0.4 seconds, attempting to reach home position. NOTE: PI50 and M41 are located on the stapler assembly and can only be replaced by replacing entire stapler assembly. M41 (Staple Motor) drives the insertion and crimping of the staple only (not location of the staple on paper). PI50 senses the home position of the stapler as it is inserting and crimping a staple only (not location of the staple on the paper). The stapler-safety switch (MS34) that assures that stapler motor (M41) is disabled when it senses a finger may be in the stapler.

66.12.22

- code :

66.12.22

- affichage :

66.12.22

- description :

Finisher upper stapler-shift motor failure (M35) Error occurs when the stapler does not leave the stapler-shift home-position sensor (PI40) after the stapler-shift motor (M35) has driven for 5 seconds. Also occurs when the stapler fails to return to the stapler-shift home-position sensor (PI40) after the stapler-shift motor (M35) has been driven for 20 seconds.

66.12.23

- code :

66.12.23

- affichage :

66.12.23

- description :

Finisher upper stapler failure Occurs when stapler-alignment-interference sensor (PI46) is activated, signaling that the stapler unit is not in its proper position for stapling to occur. This is to prevent damage to stapler from occurring when stapler is positioned over one of the three stoppers when the signal to staple has been sent.

66.12.31

- code :

66.12.31

- affichage :

66.12.31

- description :

Finisher error - 1st-tray lift/lower motor (M37) Occurs when the output-bin 1 does not activate the home-position sensor (PI41) when the output-bin-1-shift motor (M37) is driven for 20 seconds. Also occurs when output-bin 1 does not move when output-bin-1-shift motor (M37) is driven for 4 seconds. Also occurs when the output-bin-1 switch (MSW33) is activated while output-bin 1 is operating. NOTE: Output-bin-1 home position is detected using the top sheet of paper on the bin when paper is present and the edge of the bin itself when there is no paper on the bin.

66.12.32

- code :

66.12.32

- affichage :

66.12.32

- description :

Finisher error: second-tray lift/lower motor (M38) Occurs when the output-bin 2 does not activate the home-position sensor (PI48) when the output-bin-1 shift motor (M38) is driven for 20 seconds. Also occurs when output-bin 2 does not move when output-bin-1–shift motor (M38) is driven for 4 seconds. Also occurs when bin-2 upper limit is detected by PS983, PS982, PS981 on the Tray-2-shift PCA when no paper has been sensed by the output-bin-2 paper sensor (PI43). NOTE: output-bin-2 home position is detected using the top sheet of paper on the bin when paper is present and the edge of the bin itself when there is no paper on the bin.

66.12.34

- code :

66.12.34

- affichage :

66.12.34 Output accessory failure

- description :

An output accessory is not functioning properly.

66.12.41

- code :

66.12.41

- affichage :

66.12.41

- description :

Finisher: folding-paper-positioning-plate motor (M4) The paper-positioning-plate motor (M4), located in the booklet making area of the finisher, controls the Up and down positioning of the stacked paper for stitch stapling and for folding. Error occurs when the paper-positioningplate home-position sensor (PI7) does not turn on when the paper-positioning-plate motor (M4) has been driven for 1500 pulses. Also occurs when the paper-positioning-plate home-position sensor (PI7) does not turn off when the paper-positioning-plate motor (M4) has been driven for 300 pulses.

66.12.42

- code :

66.12.42

- affichage :

66.12.42

- description :

Finisher error: folding-guide motor (M3) The guide motor (M3), located in the bookletmaking area of the finisher, controls the position of the guide plate. The guide plate is positioned in front of the folding rollers as the paper stack is being stapled, allowing the bottom edge of the paper to smoothly pass by the folding rollers. When the stacked paper is lowered to the folding position, the guide motor (M3) lowers the guide plate out of the way to allow the paper stack to be pushed into the folding rollers. Error occurs when The guide-home-position sensor (PI13) does not turn on when the guide motor (M3) has been driven for 700 pulses. Also occurs when the guide-home-position sensor (PI13) does not turn off when the guide motor (M3) has been driven for 50 pulses.

66.12.43

- code :

66.12.43

- affichage :

66.12.43

- description :

Finisher error: paper-fold motor (M2) M2: paper-fold motor, located in the booklet making area of the finisher, drives the rotation of the folding rollers to create the desired fold in the paper. The error occurs when the number of pulses by the paper-fold-motor clock sensor (PI4) is less than expected standard value. Also occurs when the status of the paper-fold home-position sensor (PI21) does not change when the paper-fold motor (M2) has been driven for 3 seconds.

66.12.44

- code :

66.12.44

- affichage :

66.12.44

- description :

Finisher - folding-paper-alignment motor (M5) M5 - The alignment motor, located in the booklet making area of the finisher, drives the two alignment plates that adjust the side edges of the stacked paper so that the paper in the stack is perfectly aligned with one another. Error occurs when the aligning-plate homeposition sensor (PI5) does not turn on when the aligning-plate motor (M5) has been driven for 500 pulses. Also occurs when the aligning-plate homeposition sensor (PI5) does not turn off when the aligning-plate motor (M5) has been driven for 50 pulses.

66.12.45

- code :

66.12.45

- affichage :

66.12.45

- description :

Finisher - paper-pushing-plate motor (M8) Error occurs when the paper-pushing-plate home-position sensor (PI14) does not turn on when the paper-pushing-plate motor (M8) has been driven for 0.3 seconds. Also occurs when the paper-pushing-plate home-position sensor (PI14) does not turn off when the paper-pushing-plate motor (M8) has been driven for 80 ms. Also occurs when the paper-pushing-plate leading-edge-position sensor (PI15) does not turn off when the paper-pushing-plate motor (M8) has been driven for 80 ms. Also occurs when the number of pulses detected by the paper-pushing-plate-motor clock sensor (PI1) is less than expected standard value. Also occurs when the paper-pushing-plate leading-edge-position sensor (PI15) does not turn on when the paper-pushing-plate motor (M8) has been driven for 0.3 seconds.

66.12.46

- code :

66.12.46

- affichage :

66.12.46

- description :

Finisher - Communication Lost with Stitcher Controller PCA Error occurs when communication between the stacker-controller board and the saddlestitcher- controller board has been lost or interrupted.

66.12.47

- code :

66.12.47

- affichage :

66.12.47

- description :

Finisher error - micro switches - doors There are three switches in the bookletmaker finisher: SW1 (saddle-guide switch also known as the inlet-door switch), SW3 the booklet-ejection-door switch, and MS31 the front-door switch. The stapler/stacker finisher only has one switch, MS31 for the front door of the finisher. All three switches detect if the associated door or guide plate is open or closed. Each of the switches also have a sensor (SW1/PI9, SW3/PI3, and MS31/PI32) that acts as a backup and detects the same information as the switches. The error occurs when all the doors and guides are closed and there is a mismatch in readings between the sensors and the switches. For example, the front finisher door is closed, PI32 senses the door is closed and MS31 senses the door is still open. Associated finisher door and guide switches and sensors are as follows: • Saddle-guide switch SW1 and saddleguide sensor PI9 • Booklet-ejection-door switch SW3 and booklet-ejection-door sensor PI3 • Front-door switch MS31 and front-door sensor PI32

66.12.51

- code :

66.12.51

- affichage :

66.12.51

- description :

Finisher error- rear-booklet-stapler motor (M6) The booklet-maker stitch staplers do not move to different locations in relation to the paper like the main stapler. The only movement is through the movement of the rotary cam located on the stapler unit itself, during the actual stapling of the booklet. The stitch-home-position switch (SW5) is part of the rear-stitch stapler unit and senses the stapler opening and closing during stapling by the motion of the rotary drive cam. Like SW5, the stitch motor (M6) is also part of the overall-stitch stapler unit and replacement requires the replacement of saddle-stapler assembly. Error occurs when the front booklet-makerstapler stitching-home-position sensor (SW5) does not turn on when the stitch motor (rear) (M6) has been driven forward for 0.5 seconds. Also occurs when the front booklet-makerstapler stitching-home-position sensor (SW5) does not turn off when the stitch motor (rear) (M6) has been driven forward for 0.5 seconds.

66.12.52

- code :

66.12.52

- affichage :

66.12.52

- description :

Finisher error - front booklet-stapler motor (M7) The booklet-maker stitch staplers do not move to different locations in relation to the paper like the main stapler. The only movement is through the movement of the rotary cam located on the stapler unit itself, during the actual stapling of the booklet. The stitch-home-position switch (SW7) is part of the front-stitch stapler unit and senses the stapler opening and closing during stapling by the motion of the rotary drive cam. Like SW7, the stitch motor (M7) is also part of the overall-stitch stapler unit and replacement requires the replacement of saddle-stapler assembly. Error occurs when the front booklet-maker stapler-stitching home-position sensor (SW7) does not turn ON when the stitch motor (Front)(M7) has been driven forward for 0.5 seconds. Also occurs when the front booklet-maker stapler-stitching home-position sensor (SW7) does not turn off when the stitch motor (front) (M7) has been driven forward for 0.5 seconds.

66.XY.ZZ

- code :

66.XY.ZZ

- affichage :

66.XY.ZZ Output device failure

- description :

An error occurred in an external paperhandling accessory.

68.X

- code :

68.X

- affichage :

68.X Storage error settings changed

- description :

At least one of the settings saved in the nonvolatile storage device is invalid and was reset to its factory default. Printing can continue, but there may be some unexpected behavior because an error occurred in permanent storage. • 68.0: The onboard NVRAM failed. • 68.1: The removable disk (flash or hard) failed.

69.X

- code :

69.X

- affichage :

69.X Error

- description :

A duplex error occurred.

79.XXXX

- code :

79.XXXX

- affichage :

79.XXXX - ERROR

- description :

A critical hardware error occurred.

8X.YYYY

- code :

8X.YYYY

- affichage :

8X.YYYY EMBEDDED JETDIRECT ERROR

- description :

The embedded HP Jetdirect print server encountered a critical error, as specified by YYYY.

Le problème provient probablement d'une pièce à remplacer.

Pièces d'usures remplacées frequemment sur la HP Color LaserJet CM6040, CM6040F

Nomenclature des pièces détachées de la HP Color LaserJet CM6040, CM6040F

CC516-69002IPTU Service unit
RL1-1289-000CNROLLER (PATIN, GALET D’ENTRAINEMENT), PICK
Q3931-67935110-127V FUSER KIT (FOUR, UNITÉ DE FUSION, KIT DE MAINTENANCE) Kit Part Number
Q3931-67914110-127V FUSER KIT (FOUR, UNITÉ DE FUSION, KIT DE MAINTENANCE) Kit Part Number
Q3931-69001110V Fuser kit (Four, unité de fusion, kit de maintenance) Repaired
XA9-1500-000CN2.5ew, S, M3x8
Q3931-67936220-240V FUSER KIT (FOUR, UNITÉ DE FUSION, KIT DE MAINTENANCE) Kit
Q3931-69002220V Fuser kit (Four, unité de fusion, kit de maintenance) Repaired
RM1-3319-000CN2ND TRNSFR. ROLLER (PATIN, GALET D’ENTRAINEMENT) ASS Y
CB474-69001500 sheet feeder Kit
Q3931-67904512MB 167MHz 200 pin DDR DIMM
Q3938-67947ADF COVER LEFT
Q3938-67954ADF COVER PICK ROLLER (PATIN, GALET D’ENTRAINEMENT)
Q3938-67953ADF DIVERTER
Q3938-67945ADF ENCAP BACK
Q3938-67946ADF ENDCAP FRONT
Q3938-67951ADF FLAG SENSOR
Q3938-67991ADF HINGE ASSY
Q3938-67952ADF HINGE ASSY
Q3938-67969ADF Roller (Patin, galet d’entrainement) Kit (60K life)
Q3938-67999ADF Roller (Patin, galet d’entrainement) kit 60K/Maint
Q7829-67908ADF ROUTER CABLE
Q3938-67992ADF SCANNER CABLE
Q3938-67948ADF Scanner Cable
Q3938-68000ADF Separation Assembly
Q3938-67949ADF Separation Assy
Q3938-67995ADF Separation Assy
Q7829-67915ADF SOLENOID
Q3938-67950ADF TRAY INPUT ASSY
Q3938-67990ADF UNIT CM6030/6040
Q3938-67993ADF Unit CM6030/6040
Q3938-67998ADF Unit CM6030/6040-Spare
RC1-9189-000CNARM, 1ST ESTRANGEMENT
RL1-1272-000CNARM, AUXILIARY
RC1-9913-000CNARM, LOCK
5851-9001Assembly-Control Panel
5851-2768Assembly-Control Panel
RM1-3581-050CNAssembly-DC Controller PCB, 1.61
RM1-6642-080CNAssembly-DC Controller PCB, 1.80
RM1-3581-080CNAssembly-DC Controller PCB, 1.83
RM1-6642-090CNAssembly-DC Controller PCB, R1.84
Q3938-60103Assembly-Faceplate Formatter
RM1-0036-020CNAssembly-Paper Pick-up Roller (Patin, galet d’entrainement)
CE664-69008ASSEMBLY-SCANNER SERVICE
CE664-69002Assembly-Scanner, Service
CE664-69004ASSEMBLY-SCANNER, SERVICE
Q3938-67984Assy Power Supply with Packing
Q3938-67906Assy,Glass,w/Packing,Kauai,Spare Parts
Q3938-67907Assy,Lidsensor,w/Packing
Q3938-67908Assy,Motor,w/Packing,Kauai,Spare Parts
Q3938-67903Assy,Plate,Large Pin-P
Q3938-67904Assy,Plate,Small Pin-P
Q3938-67909Assy,Pulley,w/Packing,Kauai,Spare Parts
RM1-3531-060CNAUTO CLOSE ASS Y
RM1-3531-000CNAUTO CLOSE ASS Y
RC1-9043-000CNBAND, DOOR
Q3938-67914Base,Sensor 1,PC+ABS,47.3*50.0*6.5
XG9-0586-000CNBEARING, BALL
RC1-9674-000CNBELT, PAPER FEED, COGGED
Q3938-67935Belt,Timing,CR,1.5Kgf,557T,1131.824*5
CB390-67901Black Print Cartouche, toner (Replacement)
RC1-9922-000CNBOX, STOCK
RC1-9915-000CNBUSHING
RC1-4585-000CNBUSHING
RC1-8734-000CNBUSHING
RC1-9300-000CNBUTTON, MAIN SWITCH
RM1-3258-000CNC.P.R. SENSOR ASS Y
RM1-3561-000CNCABLE, DRAWER
RM1-3560-000CNCABLE, DRAWER
RM1-5029-000CNCABLE, FIXING OPEN SENSOR
RK2-1356-000CNCABLE, FLEXIBLE FLAT
RK2-1355-000CNCABLE, LASER FLEXIBLE FLAT
RK2-1354-000CNCABLE, LASER FLEXIBLE FLAT
RM1-3599-000CNCABLE, MFP AC
RM1-3563-000CNCABLE, MOTOR
RM1-3564-000CNCABLE, MOTOR
RM1-3574-000CNCABLE, OPT. SENSOR PCB CONNECT
RM1-3575-000CNCABLE, PAPER PICK-UP OPTION
RM1-3571-000CNCABLE, PICK-UP OPTION DRAWER
RM1-5030-000CNCABLE, TP/T2 OPEN SENSOR
Q3938-67912Cable,Flat,28(1.0),940,A,Kauai
Q3938-67913Cable,Flat,28(1.0),970,B,Kauai
Q3938-67942Cable,PCIE,28(18),74576-001,1.0M,Black
RM1-3572-000CNCABLE,PICK-UP OPT. DOOR SWITCH
RM1-3573-000CNCABLE,PICK-UP OPT. PCB CONNECT
5851-1887Cable-Hard Disk Drive Data
5851-2501Cable-SATA Power
Q3701-60103CA-MFP Analog 300 Fax
5851-1821Card Guide-EIO
Q3938-67901Carriage Assembly
Q3938-67973Carriage Assembly
RM1-3254-000CNCARTOUCHE, TONER CONTACT HOLDER ASS Y
RM1-4419-000CNCARTOUCHE, TONER INTERFACE ASSY
RM1-3283-000CNCARTOUCHE, TONER INTERFACE ASSY
RM1-3202-040CNCASSETTE ASS Y
Q3931-67918CASSETTE ASSY Kit
RM1-3212-000CNCassette Front Assembly
RM1-3206-000CNCASSETTE PAPER PICK-UP ASS Y
Q3938-67955Cassette Tray 2
Q3931-67923CASSETTE Tray 3 or 4 or 5 Kit
Q3938-67956Cassette Tray 3-5
RM1-3529-000CNCASSETTE
RC3-2994-000CNCASTER REAR
RC1-9896-000CNCASTER, DOUBLE LOCK, FRONT
RC1-9917-000CNCASTER, REAR
Q3938-67996China Kit CE878A PCA Replacement
WT2-5738-000CNClamp, Cable
WT2-5912-000CNCLAMP, FFC
WT2-5694-000CNCLIP CLAMP, WIRE
Q3938-67968BULKCLJ CP6015/CM6030/CM6040 Roller (Patin, galet d’entrainement) Kit
5090-3379CLOTH, TONER CLEANING
VS1-7177-002CNCONNECTOR, 2P
VS1-7257-012CNCONNECTOR, DRAWER
VS1-7258-014CNCONNECTOR, DRAWER
Q3938-67963Control Panel
Q3938-60163Control Panel Overlay Kit- Icon
RC1-9705-000CNCOVER, ASSIST, LEFT
RC1-9706-000CNCOVER, ASSIST, RIGHT
RC1-9666-000CNCOVER, BACK
RC1-9649-000CNCOVER, BLANKING
RC1-9201-000CNCOVER, CASSETTE BACK END
Q3931-67905COVER, FACE-DOWN
RC1-9340-000CNCOVER, FACE-DOWN
RC1-9360-000CNCOVER, FACE-DOWN DRIVE
RC1-9873-000CNCOVER, FRONT UPPER
RC1-9350-000CNCOVER, FRONT, UPPER
RC1-9667-000CNCOVER, INTERMEDIATE FEED SW.
RC1-9348-000CNCOVER, INTERNAL, RIGHT
RC1-9872-000CNCOVER, LEFT
RC1-9336-000CNCOVER, LEFT
RC1-9211-000CNCOVER, MAIN SWITCH
RC1-9511-000CNCOVER, MOTOR
RC1-8527-000CNCOVER, MULTI-PURPOSE BLANKING
RC1-9351-000CNCOVER, PAPER DELIVERY
RC1-9871-000CNCOVER, REAR
RL1-1210-000CNCOVER, REAR
RC1-9344-000CNCOVER, REAR LEFT
RC1-9703-000CNCOVER, REAR UPPER
RL1-1322-000CNCOVER, RIGHT FRONT
RL1-1321-000CNCOVER, RIGHT FRONT
RC1-9874-000CNCOVER, RIGHT LOWER
Q3938-67926Cover,ID Part Front,PC+ABS,653*246*214
Q3938-67920Cover,ID Part Left_1,PC+ABS,345*64*28
Q3938-67921Cover,ID Part Left_2,PC+ABS,482*282*75
Q3938-67925Cover,ID Part Rear,PC+ABS,704*244*113
Q3938-67922Cover,ID Part Right_1,PC+ABS,342*81*37
Q3938-67923Cover,ID Part Right_2,PC+ABS,535*104*14
Q3938-67924Cover,ID Part Top,PC+ABS,594*95*23
RM1-3624-000CNCPR JOINT CABLE
RM1-3688-000CNDAMPER ASS Y
RM1-3682-000CNDAMPER GEAR ASS Y
RC1-8925-000CNDAMPER, GEAR
RM1-3610-000CNDC CONT. POWER CABLE
RM1-6642-000CNDC CONTROLLER PCB ASS Y
RM1-3581-000CNDC CONTROLLER PCB ASS Y
RM1-6642-060CNDC CONTROLLER PCB ASSY
RM1-3581-070CNDC CONTROLLER PCB ASSY
RM1-4519-000CNDC MOTOR ASS Y
RC1-9921-000CNDOOR, STOCK
VS1-7258-012CNDrawer connector
RM1-3684-000CNDRIVE BELT ASS Y
RM1-3684-020CNDRIVE BELT ASSY
0950-4803DRIVE HARD 80GB DISC 2.5- SATA ROHS
RM1-3286-000CNDRUM MOTOR ASS Y
RC1-8961-000CNDUCT, AIR
RC1-9276-000CNDUCT, CARTOUCHE, TONER
RC1-8964-000CNDUCT, FACE-DOWN JOINT
RC1-9334-000CNDUCT, SCANNER
RC1-9309-000CNDUCT, SCANNER FAN
RM1-5949-000CNDuplex Switchback Tray
Q3938-67964Duplex Switchback Tray
RM1-3665-000CNDUPLEXING FEED ASS Y
RM1-3652-000CNDUPLEXING REVERSE ASS Y
RM1-3652-040CNDUPLEXING REVERSE ASSY
Q3938-60132Entire Scanner without Power Supply, Boa
RM1-4110-000CNENTRANCE LOWER GUIDE ASSY
RM1-4172-000CNENTRANCE UPPER GUIDE ASSY
Q3938-67957Face Down Cover
RM1-3340-000CNFACE-DOWN END TRAY ASS Y
RM1-4391-000CNFACE-DOWN FULL FLAG ASS Y
RM1-3293-010CNFACE-DOWN PAPER DELIVERY ASS Y
RM1-3293-000CNFACE-DOWN PAPER DELIVERY ASS Y
RM1-3390-000CNFACE-DOWN UNIT 1 CABLE
RM1-3391-000CNFACE-DOWN UNIT 2 CABLE
RK2-1382-000CNFAN
RK2-1377-000CNFAN
RK2-1378-000CNFAN
RM1-4394-000CNFAN ASS Y
RM1-3364-000CNFAN ASS Y
Q3938-67938Fan,Sleeve,DC24V
Q3938-67937Fan,Sleeve,DC24V,0.17A
Q3938-67939Fan,Vapo,DC,24V,0.1A
RL1-1291-000CNFILTER UNIT, AIR
Q3931-67906FILTER UNIT, AIR Kit Part Number
RC1-9313-000CNFILTER UNIT, AIR
RM1-3685-000CNFIN LOCK ASS Y
RM1-3242-000CNFIXING ASS Y
RM1-3242-020CNFIXING ASS Y
RM1-3244-000CNFIXING ASS Y
Q3931-67940Fixing Assembly Kit
Q3931-67941Fixing Assembly kit
RM1-3242-030CNFUSER KIT (FOUR, UNITÉ DE FUSION, KIT DE MAINTENANCE)
RM1-3244-030CNFUSER KIT (FOUR, UNITÉ DE FUSION, KIT DE MAINTENANCE)
RM1-4409-000CNFIXING BIAS CABLE ASS Y
RM1-5950-000CNFIXING FAN COVER ASS Y
RM1-3612-000CNFIXING JOINT CABLE
RM1-3217-000CNFIXING MOTOR CABLE
RM1-3247-020CNFIXING ONE-WAY
RM1-3247-000CNFIXING ONE-WAY GEAR ASS Y
RM1-3218-000CNFIXING POWER SUPPLY ASS Y
RC1-9620-000CNFLANGE, PULLEY
RC1-9208-000CNFOOT, RUBBER
RM1-3253-000CNFORMATTER CASE ASS Y
Q3938-67960Formatter
RM1-5953-000CNFR. INTERNAL SMALL COVER ASS Y
RM1-3617-000CNFRONT CABLE
RM1-3357-000CNFRONT COVER ASS Y
RM1-4122-000CNFRONT DOOR ASS Y
Q6998-67901Front Door Assembly
RM1-4134-000CNFront Door Assembly
Q6999-67901Front Door Assy
RM1-4404-000CNFRONT INTERNAL COVER ASS Y
RU5-0791-000CNGEAR, 34T
RU5-0790-000CNGEAR, 83T/25T
RM1-3225-000CNGRIP SUPPORT FRONT ASS Y
RM1-3226-000CNGRIP SUPPORT REAR ASS Y
Q3938-67915Guide Glass,Rubber,20*4.0*t1.0
RM1-4400-000CNGUIDE SENSOR ASS Y
RC1-9688-000CNGUIDE, CABLE, 2
RC1-9306-000CNGUIDE, CABLE, A
RC1-9307-000CNGUIDE, CABLE, B
RC1-9308-000CNGUIDE, CABLE, C
RC1-9312-000CNGUIDE, CABLE, D
RC1-9318-000CNGUIDE, CABLE, E
RC1-9323-000CNGUIDE, CABLE, F
RL1-1335-000CNGUIDE, DUPLEXING FEED, UPPER
RC1-8959-000CNGUIDE, FACE-DOWN INNER
RC1-9332-000CNGUIDE, FIXING CABLE
RC1-9185-000CNGUIDE, I.T.B. ENTRANCE, FRONT
RC1-9186-000CNGUIDE, I.T.B. ENTRANCE, REAR
RL1-1283-000CNGUIDE, MULTI-PURPOSE, RIGHT
RC1-8526-000CNGUIDE, MULTI-PURPOSE, UPPER
RC1-8526-020CNGUIDE, MULTI-PURPOSE, UPPER
RC1-9881-000CNGUIDE, PAPER FEED ROLLER (PATIN, GALET D’ENTRAINEMENT)
Q3938-67961Hard Drive
Q3938-67928Harness,PowerControl
Q7829-67924HCI PICKUP ROLLER (PATIN, GALET D’ENTRAINEMENT) (WHITE)
RM1-3582-000CNHIGH VOLTAGE TRAN. A PCB ASS Y
RM1-5475-000CNHIGH VOLTAGE TRAN. B PCB ASS Y
RC1-9277-000CNHOLDER, CARTOUCHE, TONER FAN
RC1-9324-000CNHOLDER, ENVIRONMENT SENSOR
RC1-9278-000CNHOLDER, FIXING FAN
RC1-9328-000CNHOLDER, HIGH VOLTAGE CONNECTOR
RC1-9279-000CNHOLDER, SCANNER FAN
RC1-9260-000CNHOLDER, SCANNER THERMISTOR
Q7559-60001HP 512MB 167HMZ 200 PIN DDR DIMM
CB384-67901HP CLJ Black Image Drum CB384A
CB380-67901HP CLJ Blk Print Cartouche, toner
CB385-67901HP CLJ Cyan Image Drum CB385A
CB381-67901HP CLJ Cyan Print Cartouche, toner
CB387-67901HP CLJ Magenta Image Drum CB387A
CB383-67901HP CLJ Magenta Print Cartouche, toner
CB386-67901HP CLJ Yellow Image Drum CB386A
CB382-67901HP CLJ Yellow Print Cartouche, toner
CB457AHP Color LaserJet 110volt Fuser kit (Four, unité de fusion, kit de maintenance) KiT
RM1-3240-000CNI.T.B. DRAWER ASS Y
RM1-4401-000CNI.T.B. DUCT ASS Y
RM1-3280-000CNI.T.B. ESTRANG. DRIVE ASS Y
RM1-3216-000CNI.T.B. GEAR HOLDER ASS Y
RM1-3215-000CNI.T.B. LOCK SUPPORT REAR ASS Y
RM1-3228-000CNI.T.B.LOCK SUPPORT FRONT ASS Y
Q3938-67966Image Fuser kit (Four, unité de fusion, kit de maintenance) Kit (110V) (100K life)
Q3938-67967Image Fuser kit (Four, unité de fusion, kit de maintenance) Kit (220V) (100K life)
Q3938-67989-BUImage transfer assembly
Q3938-67987Image Transfer Kit (150K life)
Q3938-68001IMAGE TRANSFER KIT (150K LIFE)
Q3938-67965Image Transfer Kit (150K life)
Q3938-67989IMAGE TRANSFER KIT (150K LIFE)
RM1-3623-000CNINTERFACE JOINT CABLE
RM1-3589-000CNINTERLOCK SWITCH ASS Y
RM1-3307-000CNINTERMEDIATE TRANS. BELT ASS Y
RM1-3307-040CNINTERMEDIATE TRANS. BELT ASS Y
RM1-3307-BULKINTERMEDIATE TRANS. BELT ASS Y
RC1-9348-020CNINTERNAL RIGHT COVER
Q3938-67905Inverter Assembly
RM1-3559-000CNIPTU DRIVER PCB ASS Y
Q3931-67938Kit of 12 rollers- 1 set tray 2 to 5
Q3931-67938BULKKit of 12 rollers-1 set tray 2 to 5
Q3938-67997Kit-CE878A PCA replace 52,071,4 Rohs2.04
Q3938-67979Kit-CE878A PCA replacement 52.051.3
Q3938-67982Kit-CE878A PCA replacement 52.071.4
Q3938-60129Kit-Control Panel Overlay AR
Q3938-60120Kit-Control Panel Overlay CS
Q3938-60117Kit-Control Panel Overlay DA
Q3938-60110Kit-Control Panel Overlay DE
Q3938-60128Kit-Control Panel Overlay EL
Q3938-60107Kit-Control Panel Overlay EN
Q3938-60111Kit-Control Panel Overlay ES
Q3938-60116Kit-Control Panel Overlay FI
Q3938-60108Kit-Control Panel Overlay FR
Q3938-60127Kit-Control Panel Overlay HE
Q3938-60121Kit-Control Panel Overlay HU
Q3938-60109Kit-Control Panel Overlay IT
Q3938-60125Kit-Control Panel Overlay JA
Q3938-60124Kit-Control Panel Overlay KO
Q3938-60112Kit-Control Panel Overlay NL
Q3938-60114Kit-Control Panel Overlay NO
Q3938-60118Kit-Control Panel Overlay PL
Q3938-60113Kit-Control Panel Overlay PT
Q3938-60119Kit-Control Panel Overlay RU
Q3938-60115Kit-Control Panel Overlay SV
Q3938-60130Kit-Control Panel Overlay TH
Q3938-60126Kit-Control Panel Overlay TR
Q3938-60156Kit-Control Panel Overlay ZHCN
Q3938-60123Kit-Control Panel Overlay ZHCN
Q3938-60155Kit-Control Panel Overlay ZHTW
Q3938-60122Kit-Control Panel Overlay ZHTW
Q3938-67986Kit-DC Controller w/service doc, 1.84
Q3938-67972Kit-Optical Scanner-Inverter
Q3938-67977Kit-Q7542A PCA replacement 52.071.4
5851-3941Kit-Roller (Patin, galet d’entrainement)
Q3931-67939Latch Hooks for 2nd Transfer Assy
RM1-4396-000CNLEFT ASSIST ASS Y
RM1-3233-000CNLEFT SIDE WALL ASS Y
RC1-9220-000CNLEVER, DOOR INTERLOCK SHUTTER
RC1-9883-000CNLEVER, LOCK
RC1-8928-000CNLEVER, PAPER SENSING
RM1-3222-000CNLIFTER DRIVE ASS Y
RM1-3222-020CNLIFTER DRIVE ASS Y
RM1-3222-150CNLifter drive assy
RC1-8519-000CNLIMITTER, TORQUE
Q3938-67944LJM5035/5025mfp ADF Maintenance Kit
Q3938-67943LJM5035/5025mfp ADF Unit
RM2-0190-000CNLOW VOLTAGE POWER SUPPLY ASS Y
RM1-3594-000CNLOW VOLTAGE POWER SUPPLY ASS Y
RM1-3686-000CNLOWER GUIDE ASS Y
RM1-3345-110CNM.P. PAPER PICK-UP ASS Y
RM1-3345-000CNM.P. PAPER PICK-UP ASS Y
XA9-0912-000CNM5x12 Screw w/washer
RM1-4139-050CNMAIN CONTROLLER PCB ASSY
RM1-4139-000CNMAIN CONTROLLER PCB ASSY
RM1-4416-030CNMain Drive Unit
RM1-4416-000CNMAIN DRIVE UNIT
RM1-3252-000CNMAIN SWITCH HOLDER ASS Y
Q3938-67962Memory
RM1-3585-000CNMEMORY TAG PCB ASS Y
RK2-1331-000CNMOTOR, STEPPING, DC
RK2-1370-000CNMOTOR, STEPPING, DC
RK2-1366-000CNMOTOR, STEPPING, DC
RK2-1320-000CNMOTOR, STEPPING, DC
RM1-3630-000CNMULTI TRAY CABLE
RM1-3366-010CNMULTI-PURPOSE DRIVE ASS Y
RM1-3366-000CNMULTI-PURPOSE DRIVE ASS Y
RM1-3291-000CNMULTI-PURPOSE GUIDE ASS Y
RM1-3341-000CNMULTI-PURPOSE TRAY ASS Y
PF2288K050NIMylar Kit
PF2288K050NI-5Mylar Kit
RM1-4125-000CNOPERATION TRAY ASSY
RM1-3570-000CNOPTION PAPER SENSOR PCB ASSY
RM1-4105-000CNOUTPUT BIN 2 (STACK LOWER TRAY ASSY)
RM1-3389-000CNPANEL CABLE
RM1-3622-000CNPANEL JOINT CABLE
RM1-4407-000CNPAPER DELIVERY GUIDE ASS Y
4G3-0934-000CNPAPER FACE SENSOR ASSY
RM1-3569-000CNPAPER FEED PCB ASS Y
RM1-3569-030CNPAPER FEED PCB ASSY
RM1-0037-020CNPAPER FEED ROLLER (PATIN, GALET D’ENTRAINEMENT) ASSY
RM1-3533-000CNPAPER PICK-UP ASS Y
RM1-3533-010CNPAPER PICK-UP ASSY
RM1-3238-000CNPARTITION PLATE ASS Y, CYAN
RM1-3237-000CNPARTITION PLATE ASS Y, MAGENTA
RM1-3235-000CNPARTITION PLATE ASS Y, YELLOW
Q7829-67942PCA motor assembly ADF
Q7542-60003PCA-Formatter CLJ CM6040 MFP Printer
Q3701-60021PCA-MFP ANALOG 300 ROHS FAX
Q3701-60014PCA-MFP Analog 300 RoHS Fax 2.35u
Q3701-60020PCA-MFP Analog 300 RoHS Fax
Q3938-67940PCBA,Turnkey,CPB,Kauai
Q3938-67941PCBA,Turnkey,SDC,Kauai
PHA000151Pharos PC Prox Plus Card Reader
WG8-5696-000CNPhoto interrupter, TLP1243
RM1-3250-000CNPHOTOSENSOR ASS Y
XD9-0240-000CNPIN, DOWEL
RC1-9695-000CNPLATE, ASSIST ARM CAP
RC1-9235-000CNPLATE, DRAWER GUARD
RC1-9190-000CNPLATE, FAN FIXING, FRONT
RL1-1216-000CNPLATE, FIXING MOTOR
RC1-9607-000CNPLATE, GUIDE HOLD
RC1-9326-000CNPLATE, HVT-A GUARD
RC1-9246-000CNPLATE, SENSOR, FRONT
RC1-9901-000CNPLATE, SWITCH COVER
Q3938-67910Power Supply Assembly
RU5-0868-000CNPULLEY/GEAR, 22T
5851-1822radle-Disk Drive
RL1-1311-000CNRAIL, CASSETTE, LEFT
RL1-1215-000CNRAIL, CASSETTE, RIGHT
RL1-1310-000CNRAIL, CASSETTE, RIGHT
RC1-8931-000CNRAIL, FIXING, FRONT
RC1-8939-000CNRAIL, FIXING, REAR
RL1-1213-000CNRAIL, LEFT, TOP
RC1-9206-000CNRAIL, REVERSE, REAR
5851-2971Rail-3.5 Disk Drive
5851-2972Rail-Left Plastic
5851-2973Rail-Right Snap Plastic
RM1-3261-000CNRAS description not found
RM1-4398-000CNREADER FRONT GUIDE ASS Y
RM1-4399-000CNREADER REAR GUIDE ASS Y
RM1-3354-000CNREAR COVER MOUNT PLATE ASS Y
RM1-3618-000CNREAR LOWER CABLE
RM1-4415-000CNREAR RIGHT COVER ASS Y
RM1-3619-000CNREAR UPPER CABLE
Q3931-67909Reg 2nd transfr. Assy Kit and Service D
RM1-3310-000CNREGISTRATION 2ND TRNSFR. ASS Y
Q7829-67917Replacement - ADF FLOAT ASSY
Q7829-67910Replacement - ADF JAM COVER ASSY
Q7829-67943REPLACEMENT - ADF REFLECTOR FOAM
Q7829-67909Replacement - ADF REFLECTOR FOAM
Q7829-67903Replacement - ENDCAP BACK
Q3938-67985Replacement - Hard Drive 2.5
Q3938-67976Replacement - Hard Drive 3.5-
Q3938-67978Replacement - Hard Drive 3.5
Q3938-67994Replacement ADF Assembly-LJ M5035 mfp
Q7829-67914Replacement- ADF PHOTOINTERRUPTOR
Q7829-67940Replacement Paper Feed Roller (Patin, galet d’entrainement) Assy
RC1-8511-000CNRETAINER
FM2-0725-090CNRETURN ROLLER (PATIN, GALET D’ENTRAINEMENT) ASSY
RM1-4397-000CNRIGHT ASSIST ASS Y
RM1-3537-000CNRIGHT DOOR ASS Y
RM1-3538-000CNRIGHT DOOR ASS Y
RM1-3333-000CNRIGHT DOOR SUB ASS Y
RL1-1280-000CNRIGHT LOWER COVER ASS Y
RM1-3239-000CNRIGHT SIDE WALL ASS Y
XD9-0234-000CNRing, E
Q3938-67911Rod,SUM24L,OD12*644
Q3938-67968Roller (Patin, galet d’entrainement) Kit (150K life)
Q3938-67968-BURoller (Patin, galet d’entrainement) Kit (150K life)
RM1-0037-000CNRoller (Patin, galet d’entrainement) -Paper Feed
RC1-8567-000CNROLLER (PATIN, GALET D’ENTRAINEMENT), PAPER PICK-UP
RL1-1289BULKROLLER (PATIN, GALET D’ENTRAINEMENT), PAPER PICK-UP
RL1-1206-000CNROLLER (PATIN, GALET D’ENTRAINEMENT), PICK-UP
RC1-9231-000CNROLLER (PATIN, GALET D’ENTRAINEMENT), RAIL
RM1-4392-000CNROLLER (PATIN, GALET D’ENTRAINEMENT), RETARD
RM1-4136-000CNSADDLE PAPER FEEDER ASSY
RM1-3450-000CNSCANNER ASS Y
Q3931-67907SCANNER ASSY Kit Part Number
CE664-69009SCANNER CONTROLLER BOARD (SCB)
CE664-69001Scanner Controller Board (SCB)
CE664-69005SCANNER CONTROLLER BOARD (SCB)
Q3938-67902Scanner Controller Board (SCB)
RM1-3620-000CNSCANNER JOINT CABLE
XB4-7401-006CNSCREW
XB2-8300-607CNSCREW M3X6
XA9-1495-000CNSCREW RS M3X6
XA9-1449-000CNSCREW, RS, M3X8
XB6-7303-005CNScrew, TP, M3x30
XA9-1469-000CNSCREW, TP, M3X6
XA9-1448-000CNScrew, TP, M4X8
XA9-1422-000CNSCREW, W/WASHER, M4X12
XA9-1504-000CNSCREW,RS,M3X8
XB1-2300-407CNSCREW:M3X4 TRUSS
3030-1103SCREW-SKT HD CAP 6-32 .25-IN-LG ROHS
0515-4679SCREW-THD RLG ASSY M3 X 0.5 6MM-LG ROHS
RK2-2376-000CNSENSOR UNIT, HUMIDITY
RC1-9912-000CNSHAFT, LOCK
RC1-9687-000CNSHEET, BLANKING
RC1-9232-000CNSHEET, FIXING CROSSMEMBER
Q3938-67927Sheet,Bottom Shading,Gray 2,D10*t0.66
RM1-3683-000CNSIDE COVER ASS Y
RM1-3683-020CNSIDE COVER ASSY
RC1-9233-000CNSPRING, LEAF
RU5-2822-000CNSPRING, TENSION
RU5-2796-000CNSPRING, TENSION
RU5-2825-000CNSPRING, TORSION
RC1-9244-000CNSPRING, TORSION
RM1-4101-020CNSTACK UPPER TRAY ASSY
FM2-0721-000CNSTAPLE ASSEMBLY
Q6998-69001Stapler Stacker Finisher
RS5-9099-000CNStepped Screws
RC1-9882-000CNSTOPPER, RIGHT DOOR
RC1-9900-000CNSUPPORT, LOCK SHAFT
VT2-0001-008CNSUPPORT, PCB
RM1-4408-000CNSWITCH BACK COVER ASS Y
RM1-4411-000CNT2 GUIDE ARM ASS Y
RM1-4402-000CNTAG PCB HOLDER ASS Y
RC1-9884-000CNTAPE, DOOR
XB4-7401-005CNTapping screw Truss Head M4x10
RK2-1363-000CNTHERMISTOR UNIT
RM1-3232-000CNTHERMO PILE CASE ASS Y
RM1-4417-000CNTONER CARTOUCHE, TONER DRIVE ASS Y
RM1-4418-000CNTONER CARTOUCHE, TONER DRIVE ASS Y
Q3931-67913Toner Cartouche, toner Drive Assy Kit and Serv
RM1-3385-000CNTONER MOTOR CABLE
RM1-3383-000CNTONER MOTOR CABLE
RL1-1284-000CNTOP COVER ASS Y
RM1-4121-000CNTOP DOOR ASSY(SS)(UPPER COVER ASSEMBLY)
RM1-3230-000CNTRANSFER CONTACT HOLDER ASS Y
Q3938-67958Tray 1 Pick-up Roller (Patin, galet d’entrainement) Replacement
Q3931-67920Tray 1 pick-up, retard Roller (Patin, galet d’entrainement) Kit
Q3931-67919Tray 2 pick-up,feed Roller (Patin, galet d’entrainement) Kit
Q3938-67959Tray 2-5 Rollers
RC1-9256-000CNTRAY, SCREW
4G3-0210-000CNUPPER COVER LOCK ASSY
RM1-3687-000CNUPPER GUIDE ASS Y
RM1-4395-020CNUPPER GUIDE ASS Y
RM1-4395-000CNUPPER GUIDE ASS Y
Q6998-67902Upper Output Bin
RM1-4115-000CNUpper Output Bin(SS)-Stack Sub Tray Assy
RM1-3640-000CNWASTE TONER SENSOR CABLE
Q3938-67919Wire Harness,Fan4010,
Q3938-67936Wire Harness,Motor,4(24)
Q3938-67918Wire Harness,Panel
Q3938-67917Wire Harness,PaperSensor

Caractéristiques techniques

HP Color LaserJet CM6040, CM6040F

Vitesse noir41 ppm
Vitesse couleur 41 ppm
Bac à papier500 feuilles
Ref toner noirCB380A
Capacité toner noir16500 pages
Ref toner couleur CB381A
Capacité toner couleur 21000 pages